Category: Oil Properties

Lubrication Regimes: Understanding the Science of Lubrication

The primary purpose of lubrication is to create an acceptable lubricant film to sufficiently keep the two moving surfaces apart while allowing them to move with reduced friction. This is the ideal condition, but a lubricant can undergo a couple of different regimes before it achieves this full film format.

The figure below shows the overall relationship between film thickness and the related regime and the associated regime relationships with the coefficient of friction.

Stribeck curve showing the friction levels associated with the various lubrication regimes from Lubricants and Lubrication, Second, Completely Revised and Extended Edition edited by Theo Mang and Wilfried Dresel (2007)
Stribeck curve showing the friction levels associated with the various lubrication regimes from Lubricants and Lubrication, Second, Completely Revised and Extended Edition edited by Theo Mang and Wilfried Dresel (2007)

Boundary Lubrication

At startup or rest, lubricants are usually residing in the sump. For this example, let us think about a car at rest. Since the vehicle has not moved, all the oil should have been drained and settled in its sump at the bottom of the engine. When the car starts, all the parts on the inside will begin moving.

Only after it starts does the oil begin its swift journey from the bottom of the sump to all the moving parts. That means that there is a delay between the oil getting to perform its function or reaching the moving parts.

In boundary lubrication, the oil has not fully formed its film, and there isn’t adequate separation of the asperities.

During boundary lubrication, the oil has not fully formed its film, and there isn’t adequate separation of the asperities. In this state, wear can still occur, and it is in this state that most wear occurs. A similar situation occurs during equipment shutdown, where the components also experience this boundary state of lubrication.

The figure at the side shows the various film conditions. In boundary lubrication (c), the asperities touch, whereas they are fully separated in (a).

Surface-active additives are critical for boundary lubrication and become activated under certain conditions. One of the most popular additives is EP (Extreme pressure) additives, which become activated when temperatures are increased (usually as a result of increased friction).

A surface film is typically formed during boundary lubrication. This can be the result of physical adsorption (physisorption), Chemical adsorption, or Chemical reactions involving or not involving stearate.

Different regimes as it relates to the lubricant
Different regimes as it relates to the lubricant

Physical adsorption occurs under mild sliding conditions with light loads and low temperatures. Chemical adsorption (chemisorption), stronger than physisorption, occurs when fatty acids react with metals to form soaps, which may or may not be attached to the surface.

On the other hand, chemical reactions that do not involve a substrate allow for slightly stronger bonds than chemisorption. However, with phosphorus-containing compounds, the phosphorus exists in a soluble carrier molecule that degrades at elevated temperatures, plates out on the metal surfaces, and forms a phosphorus soap (typically found in the Antiwear additive packages).

The last and strongest bonds to protect the surface are the chemical reactions involving a substrate where sulfide layers are formed on the surface. These provide low friction and good adhesive wear resistance5.

Mixed Lubrication

This state of lubrication exists as the lubricant transitions between Boundary and Full-Film lubrication. Its average film thickness is less than 1 but greater than 0.01μm. Some exposed asperities and roller element bearings can still experience this state during their start-stop cycles or if they are experiencing excessive or shock loads. These thin films are exposed to high shear conditions, leading to increased temperatures and reducing the lubricants’ viscosity6.

During this state, antiwear and EP additives protect the surfaces (similar to boundary lubrication). Most lubricants transition through this phase, and the additive packages must be able to help protect the surfaces.

Hydrodynamic Lubrication

Coefficient of Friction for the various regimes
Coefficient of Friction for the various regimes

During this regime, the two surfaces are usually fully separated. They are thick hydrodynamic fluid films that tend to be more than 0.001 inches (25μm) in depth, experiencing pressures between 50-300psi7. Ideally, friction only results from the shearing forces of a viscous lubricant8.

In this state, the surfaces are conformal, meaning that the angles between the intersecting surfaces remain unchanged. It is important to remember this, as it differentiates the hydrodynamic regime from the elastohydrodynamic regime. As shown in the figure below, the coefficient of friction changes for the various regimes, with the hydrodynamic regime having the lowest value.

Elastohydrodynamic Lubrication (EHL)

One of the main defining factors with EHL is that the oil’s viscosity must increase as the pressure on the oil increases, such that a supporting film must be established at the very high-pressure contact areas. Due to the pressure of the lubricant, elastic deformation of the two surfaces in contact will occur. These films are thin, typically around 10-50 μinches (0.25 – 1.25μm).

The surfaces in EHL are non-conformal (unlike Hydrodynamic lubrication), and the asperities of the contacting surfaces do not touch. However, the high pressures can deform either of the contacting surfaces to ensure that a full fluid film is maintained. This can increase the coefficient of friction.

Find out more in the full article featured in Precision Lubrication Magazine.

Types of Lubricants and Their Applications

Not all lubricants are created equally! In fact, they need to be designed differently for the various applications in which they are to be used. Typically, the overarching classification of lubricants can fall under either oil or grease. However, there are further categorizations that also include solid lubricants and specialty lubricants, as there are many varying applications of lubricants.

Oil Lubricants: Characteristics and Uses

Most of us are very familiar with oils. They are liquid; we use them in our cars or trucks, but what are they? An oil is comprised of base oil and additives. The additives can be used to either enhance, suppress, or add new characteristics to the base oils2.

Typically, oils can be used in many different applications and provide the advantages of having various viscosities according to the application3. These can range from oils with a viscosity similar to that of water to oils as thick as tar.

One of the main advantages of using oils as lubricants is their ability to dissipate heat from the system. Since they are fluid and circulate, they can “move” heat away from specific components and even help to remove some contaminants.

Oils can be used in gasoline-engine passenger cars, diesel-engine applications, circulating systems, turbines, gear applications, hydraulics, compressors, or even natural gas engines. Each application represents a different ratio of additives to base oils, ranging from 30% (motor oils) to a mere 1% additive (turbine oils).

 

Grease Lubricants: Advantages and Limitations

While the industry is familiar with oils as lubricants, there are some places where grease works better than oils! Greases are oils to which a thickener has been added. As such, they comprise base oil, additives, and thickener. The thickener holds the oil in place, allowing it to perform its main functions of reducing friction and providing lubrication.

One of the main advantages of greases is their ability to stay in one place. Consider a bearing placed at a 90° or 180° angle. If oil were used to lubricate this, it would drain out very easily. However, grease stays in place and still ensures that lubrication occurs.

While staying in place is a major advantage of grease, there are also some disadvantages to using it. A couple of those include the fact that grease cannot transfer heat away from components and keeps contaminants in place. These can both negatively impact the equipment.

Similar to oil, grease has different viscosities as per the NLGI (National Lubricating Grease Institute). These range from a 000 (almost the consistency of oil) to a 6 (similar to that of a block) and are all made for varying applications, as shown in the figure below.

While these viscosities define the application, one must also remember that the base oil viscosity can also differ. As such, operators must be mindful of NLGI grade, base oil viscosity, and additive package when selecting an appropriate grease.

NLGI grades of grease

Solid Lubricants: When and Why to Use Them

Why do we need a solid lubricant if we already have oils and greases in different states? Particular applications make these lubricants mandatory as they are the only ones that can meet the conditions and specifications involved.

Unlike oils or greases, these solid lubricants are designed to work in one lubrication regime, boundary lubrication4 (more on this later in the article). What sets these lubricants apart is their ability to form very thin films on the surfaces of moving components, which reduces friction due to their very low shear strength.

Some examples of solid lubricants include graphite, Molybdenum Disulfide (MoS2), Boren Nitride, and Fluoropolymer (PTFE). These solid lubricants can usually be used as grease additives (such as MoS2 for greases in mining with high load, low-speed applications) or even in the space industry for dry lubricant coatings on spacecraft.

 

Find out more in the full article featured in Precision Lubrication Magazine.

Lubrication Explained

What is Lubrication?

Lubrication is the process of reducing friction, wear, and heat between moving surfaces by introducing a lubricating substance, such as oil or grease.

The Purpose of Lubrication

If you walk into any industrial facility, you will find lubricants. While they come in all types of textures (greases or oils), viscosities, and packaging, one thing remains true: We need them. Lubricants were designed to reduce friction as their main function. However, that’s not their only use.

Although lubricants can effectively reduce friction, they can also reduce or transfer the heat built up in machines. This only applies to oils circulated through the systems and not grease that remains in place.

Additionally, lubricants can minimize wear by providing an adequate film to separate surfaces from rubbing on each other.

The 6 Functions of a Lubricant
The 6 Functions of a Lubricant

Lubricants also help improve the efficiency of the machine by removing heat and reducing friction. They can also remove contaminants (for oils that are circulating, not grease) and transport them away from the machine’s internals. This is due to some additive technologies (such as dispersants or detergents).

Depending on the type of lubricant or its application, its function can also change. For instance, hydraulic oils are specifically used to transmit power, something that gear oils or motor oils cannot do. On the other hand, the lubricant can be considered a conduit of information if condition monitoring is considered.

Lubricants provide several functions depending on their application and environment. However, the main functions of a lubricant include reducing friction and wear, distributing heat, removing contaminants, and improving efficiency.

How Lubrication Reduces Friction and Wear

At the heart of lubrication is the main function of overcoming friction. When two parts move or two surfaces rub against each other, microscopic projections called asperities exist. Even on what appears to be smooth surfaces, asperities exist, and when these move over each other, friction is produced, which in turn can generate heat and cause wear.

Wear can typically occur in various forms, but in many of these, the touching of the asperities serves as the trigger point for wear to occur.

This is where lubricants really make a statement. They serve to provide a barrier between the two surfaces, almost allowing them to float over each other seamlessly. As such, friction is reduced once the asperities are kept apart, and this even influences a reduction in the occurrence of wear.

Wear can typically occur in various forms, but in many of these, the touching of the asperities serves as the trigger point for wear to occur. With the presence of the appropriate viscosity of lubricants, these asperities can be kept apart, and the occurrence of wear can be diminished significantly.

The Role of Lubrication in Preventive Maintenance

As we have noted above, proper lubrication can help to prevent wear. This is one of the many characteristics which make it ideally suited as a tool for preventive maintenance.

As defined, preventive maintenance can help maintenance professionals schedule time-based tasks / prescribed intervals1. Any maintenance manual will include prescribed intervals at which lubricants should be changed (typically after 500 hours or 5000km).

OEMs (Original Equipment Manufacturers) defined these intervals as general guidelines for machine operators. This gives operators an idea of the lubricant’s expected life or the duration after which it would no longer be able to perform its functions adequately. By changing the lubricants at these intervals, one could avoid unplanned downtime.

Another aspect of lubrication associated with preventive maintenance is relubrication intervals. In some machines, there are minimum required reservoir levels that need to be maintained.

However, depending on the system, there may be some expected loss of lubricants during its lifetime. As such, relubrication intervals can help prevent unwanted downtime by injecting new oil or grease (with fresh additives) and maintaining the required reservoir levels.

Storage and Handling & Advancements in Hydraulic oils

Hydraulic systems have smaller clearances than many. As such, it is imperative that these oils be kept clean and free from any debris. Most hydraulic components have a required ISO 4406 rating that should be met to ensure that the oils do not allow foreign particles to enter as these can easily clog the clearances and cause the system to stop working.

Chevron Lubricants produced a document that compiles some ISO 4406 codes for various types of industrial off highway equipment, which also includes the hydraulic standards. It noted the recommended ISO Cleanliness for John Deere hydraulic Excavators can be ≤23/21/16, this can be found here (Chevron Lubricants, 2015).

Hydraulic oils should be pre-filtered before being placed in your equipment even though there are filters on the inside of the equipment by reducing the amount of contamination entering the system from the onset, you can ensure a longer life for your hydraulic oil. Hydraulic oils should also be stored in closed containers not those that are left open to the atmosphere!

Advancements in Hydraulic Oils

According to (Fitzpatrick & Thom, 2021), the hydraulic oil market was approximately worth USD 77.5 billion by the end of 2021. Mobile hydraulics account for 65% of the market while industrial equipment represents 35% of the market. Clearly, the larger market share exists for mobile hydraulics. However, OEMs are also moving towards smaller oil sumps with longer oil drain intervals that can impact on the volume of hydraulics needed periodically.

Changes by OEMs also impact the formulation of hydraulic oils. For instance, if a smaller sump is used then, the hydraulic oil must now be able to cool faster, transport the same (or larger) force and maintain the intended viscosity of operation while being under greater stress. In these cases, the additive packages involving the antiwear, thermal stability, viscosity index improvers, defoamants and dispersants must be formulated to work in unison without compromising the other.

There have been changes in additive technology that allow for larger tolerances for various characteristics but while additives are evolving, the refining of base oils is also trying to keep up. With all of these evolutions, the chemical composition of hydraulic oil today vastly differs from one created in the 1950s. The requirements of hydraulic oil have also greatly evolved, forcing these changes in formulation.

Hydraulic oils today need to provide longer oil drain intervals, better stick/slip characteristics, increased efficiency, improved conductivity and wear performance and an added level of sustainability. Formulators need to create hydraulic oils that can adhere to these characteristics while also not infringing on regulatory requirements. This makes hydraulic oils one of the most powerful types of oils because they must conform to these requirements while also transferring force from one place to another.

References

Chevron Lubricants. (2015, January 24). Chevron Lubricants Latin America. Retrieved from Chevron Lubricants: https://latinamerica.chevronlubricants.com

Fitzpatrick, A., & Thom, M. (2021, November 08). How the Global Hydraulic Fluid Market Is Changing—And What It Means for the Future. Retrieved from Power Transmission Engineering: https://www.powertransmission.com/blogs/1-revolutions/post/189

Mang, T., & Dresel, W. (2007). Lubricants and Lubrication Second Edition. Weinheim: WILEY-VCH.

Pirro, D. M., Webster, M., & Daschner, E. (2016). Lubrication Fundamentals, Third Edition Revised and Expanded, ExxonMobil. Boca Raton: CRC Press, Taylor & Francis Group.

Are Consolidation and Cheaper Hydraulic Oils Worthwhile Considerations?

Given the various types of hydraulic oils that exist, can they all be consolidated into one hydraulic oil that can serve the purpose for all the applications? The short answer is no, the longer answer is that if there is overlap among OEM recommendations within the same viscosity, then there is a possibility of consolidation. Typically, OEMs will provide guidelines on the oils recommended for use and they should be sought out for these consolidations as they will be more familiar with compatibility issues, as well.

On the other hand, it may mean that the hydraulic storage area of the warehouse has numerous hydraulic oils. In this case, a proper labelling system should be in place to ensure that the correct oil gets to the right location. Since these are specialized, using an incorrect oil (or an oil that does not meet the right specification) can result in disastrous outcomes for the equipment especially for compatibility challenges.

One of the most common issues with hydraulic equipment is the existence of leaks. Depending on the application, some owners prefer not to fix the leaks and use cheap hydraulic oil to keep the equipment working. However, this is not the best practice.

When hydraulic oil leaks out into the environment, this can be hazardous to the people on the site (spills or trips), equipment (skids or contamination) and the environment since it was not disposed of properly. By using cheap oil, this can also damage the equipment even more as that oil may not meet the OEM requirements. In these cases, more harm is being done to the environment and the equipment and there can be significant losses financially and operationally.

This is where the quality of the oil and operations (no leaks) can trump quantity (excess volumes of cheaper oil). Unless the leaks are fixed, then the volume of cheaper oil will continue to increase and there will be additional labour costs to constantly maintain the sump levels as well as delays to the project.

Therefore, the overall impact on the efficiency of the hydraulic equipment will be reduced. However, if the leaks are fixed and a quality hydraulic oil is used, then the machine can operate more efficiently, complete the assigned projects and possibly even reduce extra labour costs related to maintenance.

Ideally, consolidation can be achieved as long as the OEM requirements are being fulfilled. However, cheaper oil that does not meet the required OEM standard for a particular piece of equipment is not an ideal option as it can cause more harm than good in the long run.

Are There Different Types of Hydraulic Oils?

Similar to there being endless types of greases, there are also many types of hydraulic oils specifically designed for certain systems. Hydraulics comprise of lots of different operations as such, they will be called upon to perform in various applications. Some of these can include being fire resistant, biodegradable or even being able to also act as an engine oil. These properties can be influenced by the type of base oil used to produce these oils. For example, fire resistant or rapidly biodegradable fluids or even specialty hydraulic fluids can use PAOs (Polyalphaolefins), PAGs (Polyalkylglycols), POE (ester oils) or other synthetic oils as their base oil.

As per (Mang & Dresel, 2007), hydraulics require special types of additives for their applications. The most important additives for hydraulic oils are:

Surface active additives – For hydraulic oils these can be rust inhibitors, metal deactivators, wear inhibitors, friction modifiers, detergents / dispersants, etc.

Base Oil active additives” – For hydraulic oils, these can be antioxidants, defoamers, VI Improvers, Pourpoint improvers, etc.

Typically, the additives for hydraulic oils can be broadly classed into those which contain zinc and ash and those which do not. Zinc and Ash free oils can represent 20-30% of hydraulic oils on the market and are used for specialty applications where the presence of zinc or ash can hamper the functionality of the equipment.

One such example is the use of these oils in the JCB Fastrac 3000 series for the hydraulic oils. These systems contain yellow metals which can be easily degraded with the presence of zinc or the filterability of the oil can be impacted due to the presence of water. Hence, zinc and ash free oils must be used in these instances.

The following shows a chart of the types of hydraulic fluids as per (Mang & Dresel, 2007) broken down by hydrokinetic applications, hydrostatic applications and mobile systems.

Figure 1: Classifications of hydraulic fluids as per (Mang & Dresel, 2007) Chapter 11, figure 11.9.
Figure 1: Classifications of hydraulic fluids as per (Mang & Dresel, 2007) Chapter 11, figure 11.9.

As seen above, there are many different classifications of hydraulic oils. To provide some clarification on the symbols used in DIN 51 502 and ISO 6743/4, (Mang & Dresel, 2007) produced this table.

Figure 2: Classification of mineral oil-based hydraulic fluids as per (Mang & Dresel, 2007), Chapter 11, Table 11.3.
Figure 2: Classification of mineral oil-based hydraulic fluids as per (Mang & Dresel, 2007), Chapter 11, Table 11.3.

When looking at hydraulic oil classifications, these categories will come up and it is important to be able to understand what each of these mean as well as how it translates to your system. Typically, the most common are the ISO HM and ISO HV.

The ISO HM refers to oils with improved anti-wear properties used in general hydraulic systems with highly loaded components and where there is a need for good water separation operating in the range of -20 to 90°C.

The ISO HV oils are HM oils with additives that improve viscosity-temperature behavior. Ideally, these are used in environments that experience significant changes in temperatures, such as construction or marine, between the ranges of -35 to 120°C.

What Are The Functions of Hydraulic Oils?

Hydraulic oils today need to provide longer oil drain intervals, better stick/slip characteristics, increased efficiency, improved conductivity and wear performance and an added level of sustainability.

Hydraulic oils are used in many areas of our life, from the telescopic booms of cranes to the control valves in a tractor. These oils are special as they perform a particular function which is unique to them. In addition to the regular functions of an oil, hydraulic oils can transmit power which truly sets them apart. In this article, we will take a deeper dive into the world of hydraulic oils, how they can be used, ways that they should be stored and handled and of course some advancements that we’ve seen over the years.

What Are The Functions of Hydraulic Oils?

Before going any further, we must understand how hydraulic oils function and the impact that they create for our equipment. As per (Pirro, Webster, & Daschner, 2016), the concept of hydraulics revolves around the transmission of force from one point to another where the fluid is the transmitter of this force. Ideally, this is based off Pascal’s Law where, “The pressure applied to a confined fluid is transmitted undiminished in all directions and acts with equal force and at right angles to them.”

As applied to hydraulic oils, once a force is exerted on an oil, the oil can transmit this force to either help an actuator turn or stop an excavator from moving (through braking). This is the transmission of pressure, but hydraulic oils can also provide the functions of reduced wear, prevention of rust and corrosion, reduction in wear and friction and an overall improvement in system efficiency.

For anyone who has worked with hydraulic oils, they will be familiar with the fact that these oils have very tight clearances which requires them to be clean. As they are transmitting power through the fluid, having clean hydraulic oil is essential, so this flow is not disrupted. Since the force will be the same throughout the lubricant, having these tighter clearances allows for more force to be output per square area at the intended target without the contaminants.

Overall, hydraulics will perform the regular functions of an oil but with the added benefit of the transmission of force for these applications. But not all hydraulic oils are created equally and some need to be specifically designed for particular applications within our industry.

The Future of Gear Oils

According to (Industry ARC (Analytics. Research. Consulting), 2024), the global industrial gear oil market size is forecasted to reach USD 5.2 B by 2027. While the Asia-Pacific market holds a significant market share for industrial gear oils in 2021 at around 56.2%, it is interesting that its nearest rival is Europe, at 17.7% or less than ⅓ of its size.

The rise in the Asia Pacific market can be accounted for due to the increase in the rising population and, by extension, the needs of that population and the service sectors they support, including the energy, oil & gas, construction, and steel industries. The figure below depicts the global industrial gear oil market revenue share by Geography for 2021.

Figure 6: Industrial Gear Oils (Mineral & Synthetic) Market Revenue Share by Geography 2021 adapted from (Industry ARC (Analytics. Research. Consulting), 2024)
Figure 6: Industrial Gear Oils (Mineral & Synthetic) Market Revenue Share by Geography 2021 adapted from (Industry ARC (Analytics. Research. Consulting), 2024)

From the research conducted by (Industry ARC (Analytics. Research. Consulting), 2024), helical gears appear to be the most popular choice for industrial gears. Interestingly enough, synthetic gear oil held the largest market share and is forecasted to grow by a CAGR of 5.6% for the forecasted period of 2022-2027.

Smaller gearboxes are being manufactured, tasked with outperforming their previous counterparts and producing more torque in a smaller space. With the advent of better, more precise machining tools for gears, there is an increase in the amount of pressure these gears now must handle in smaller spaces.

As such, we will continue to see the rise in the use of synthetic gear lubricants formulated to handle these extreme conditions, as well as more advanced additive packages that can help minimize foaming, reduce oxidation, and aid in the demulsibility of these oils.

References

Industry ARC (Analytics. Research. Consulting). (2024, September 04). Industrial Gear Oils (Mineral & Synthetic) Market - Forecast(2024 - 2030). Retrieved from Industry ARC: https://www.industryarc.com/Report/20008/industrial-gear-oils-mineral-and-synthetic-market.html

Mang, T., & Dresel, W. (2007). Lubricants and Lubrication - Second Edition. Weinheim: WILEY-VCH GmbH & Co. KGaA.

Mang, T., Bobzin, K., & Bartels, T. (2011). Industrial Tribology - Tribosystems, Friction, Wear and Surface Engineering, Lubrication. Weinheim: WILEY-VCH Verlag GmbH & Co. KGaA.

Pirro, D. M., Webster, M., & Daschner, E. (2016). Lubrication Fundamentals - Third Edition, Revised and Expanded. Boca Raton: CRC Press, Taylor & Francis Group.

Rensselar, J. v. (February 2013). Gear oils. Tribology and Lubrication Technology - STLE, 33.

Sander, J. (2020). Putting the simple back into viscosity. Retrieved from Lubrication Engineers: https://lelubricants.com/wp-content/uploads/pdf/news/White%20Papers/simple_viscosity.pdf

Santora, M. (2018, March 20). Tips on properly specifying gear oil. Retrieved from Design World: https://www.designworldonline.com/tips-on-properly-specifying-gear-oil/#:~:text=CLP%20Gear%20Oils&text=Often%2C%20a%20gear%20manufacturer%20will,a%20CLP%20polyglycol%20PAG%20oil

Gear Oil Storage and Handling

Similar to most oils, gear oils should be stored in a clean and dry space. Often (especially in the past), these gear oils see a settling of the additives to the bottom of the container, indicating a slightly shorter oil life span than other lubricants. However, this is no longer a highly occurring incident with the advancements in additive technology and improved blending practices.

As usual, it is always best to adhere to the OEM’s expiry dates for these products, as different OEMs recommend varying storage times for their products. Generally, synthetic lubricants have an estimated shelf life of 5-10 years, while mineral oils usually last for around 2-3 years, but this is heavily dependent on the OEM and storage conditions.

In some cases, customers tend to store these drums outside in the elements as it makes it easier for them to be readily accessible for decanting into the equipment. However, in these environments, the drums can collect water, which will enter the oil and then, by extension, enter the gearbox. This can cause issues for the equipment and lead to accelerated oil degradation.

Ideally, these oils should be stored in a cool, dry place with ready access to decanting equipment where the decanted oil will not be easily contaminated. Many industrial gearboxes typically require larger quantities of oil, and decanting can take place directly from the drum into the equipment or via a pump.

In these cases, the level of contamination must be minimized by ensuring that the fittings, hoses, etc., are clean and have not been used to decant other types of oils.

Degradation of Gear Oils

The first set of additives to decrease in gear oils is often the antiwear or extreme pressure additives. This is no surprise, as these oils are subjected to high levels of wear and must withstand extreme pressures. One can also notice a decline in the rust and oxidation additives or even a change in the air release values.

 

All these properties significantly impact how a gear oil functions. As such, they should be monitored when establishing the health of the oil.

When monitoring the health of these lubricants, some guidelines can be utilized. If there is a change in viscosity of either ±10%, one should look for any other correlating changes.

Typically, if the viscosity increases by 10%, we’re looking at increases in wear metals or the risk of oxidation and development of some deposits in the oil or even contamination of the oil with some water. However, for a decline of 10%, one can expect some form of contamination, typically fuel or another substance which will thin out the lubricant.

The lubricant’s warning levels for wear metals will vary depending on the manufacturer/OEM. However, any consistent rise in wear metals indicates that some component on the inside of the equipment is slowly wearing away.